- Видео 200
- Просмотров 61 642
Bikes&Bits
Добавлен 22 мар 2011
Видео
Pandora Rocks into Roots Manoeuvres. Bike Park Wales.
Просмотров 6814 дней назад
Pandora Rocks into Roots Manoeuvres. Bike Park Wales.
2022 Specialized Levo Brose Motor Bearing and Sprag Clutch Replacement
Просмотров 2,1 тыс.Месяц назад
Strip and rebuild of the Brose 2.1 S Mag 2022 Specialized Turbo Levo motor. Right hand crankshaft bearing 34x47x7mm eBike Motor Centre part number - PLB20122. Alternative bearing - 6907 LUV. Left hand crankshaft bearing 34x47x7mm eBike Motor Centre part number - PLB20121. Alternative bearing - SS6805 LLB. Inner crankshaft bearing eBike Motor Centre part number - PLB20123. Alternative bearing - ...
Finale Ligure Cacciatore Black Full Run
Просмотров 282 месяца назад
Finale Ligure Cacciatore Black Full Run
A few trails up Bike Park Wales. Yew 🤙🏼🤙🏼
Просмотров 374 месяца назад
A few trails up Bike Park Wales. Yew 🤙🏼🤙🏼
Cwmcarn Twrch, some off piste, Y Mynydd and Pedal Hounds
Просмотров 1187 месяцев назад
Cwmcarn Twrch, some off piste, Y Mynydd and Pedal Hounds
Jonkershoek MTO Trails, Stellenbosch 🇿🇦
Просмотров 3608 месяцев назад
Jonkershoek MTO Trails, Stellenbosch 🇿🇦
This is so frustrating, i know people who have 6000 miles on a motor with no faults then people with 600 miles motor failure 😮 my levo turbo 2022 model did 1000 miles and had motor replaced wasn't failed just stuck on sometimes very lightly! Just had the 2023 comp model fingers crossed 🤞🏻 feel afraid to ride it knowing this happens, but i have 2 years warranty so just guna thrash it for 2 years see what happens
For sure. I’m sure you’ll be good but if it does fail then at least you know it can be fixed. Was a pretty simple job to be honest so long as the electronic parts don’t fail. As with most electronic stuff it’s often a bin job. I would say that though as a mechanical engineer 😋. Fingers crossed.
Thank you for using our bearings. As you probably noticed, these are genuine bearings direct from Brose the motor manufacturer. You may also have noticed that the two outer crankshaft bearings are specifically designed as "anti-creep" bearings. They use the specially shaped outer seal, to stop them rotating in the case and wearing the motor housing (This damage happens, incredibly fast too!) I noticed your recommended bearings do not have this important addition. I won't mention any of the other issues, except for the bonding (gluing) of the large pulley bearing (PLB20124). As this is a magnesium case, peening it with a pop riveter doesn't work and even from the factory, this particular bearing is bonded in with a high strength bearing fit. Without this, the bearing creeps out of the housing slightly and rubs on the belt cover causing a small misalignment of the belt pulleys, which snaps the belt and fill the motor with carbon and magnesium dust... Ask me how I know :)
Many thanks for the comment and thanks for your help when I spoke to you last month. I’ve got some loctite 638 here which I’ll use for the large pulley bearing.
@@sce8arl Great, and if you need a casing when your lugs snap off, just give me a shout.
Thanks. That’s what I’m most worried about.
Pulled the motor and that main large bearing didn’t take much force to get it out of the casing. All back together with the loctite. Everything inside is still spot on with no sign of belt wear or movement of other parts.
@@sce8arl Great news that all was still ok... Any chance of taking those bearing part numbers down, people will end up with the wrong bearings from some of those.
😮😮😮😮😮😮😮
Great video! Thanks for the bearing list. Was there a seal before the needle bearing in the engine originally? You install it at 18:45.
Not on the original. That’s why the water got in. Hopefully it’s fixed the problem.
@@sce8arl Do you know the thickness of this sealant, 3mm or 4mm?
@@mateuszp374not too sure to be honest. Probably 3mm. The deeper the seal the further the roller bearing is offset which would result in the bearing not sitting in the centre of the axle load bearing area.
Interested to see how long it lasts
75 miles in and still like butter 🧈
mais vous n'avez pas changé le débrayable de la couronne crantée, la seule façon de ne pas casser la bague noire c'est de faire à l'opposé une découpe en fenêtre de 8 mm le passage étant libre vous pouvez poussé facilement sans rien cassé
All went back together as it came apart with no damage. Running sweet as a nut
How much miles do you have before rebuild the motor?
I’ve done around 1700 miles but without the water ingress it would’ve gone on way longer. The bearings not affected by the water were perfect.
@@sce8arl Damn 1700 miles and already cracked the case and needed a basic rebuild, you must thrash! Any tips on trying to keep bearings from getting wet. Great video Thank you!!!
@@Rambleon444I do tend to hammer the bike. Without the small seal that sits on the non drive side there’s no way to stop water getting in. I ride throughout the winter and take real good care of the bike, but water always finds a way in. Design fault of the motor. Hopefully it’ll last a lot longer now. Glad you liked it 🤙🏼
Great work. If the engine now runs longer than 100km without problems, then congratulations. 😋
75 miles in. Smooth as silk
@@sce8arl Wait and see. I think you have set the belt tension incorrectly. The correct setting is to set the belt to a specific torque value using a torque wrench. 🤷♂
@@ihabsgleithe suggested torque setting is 3Nm which was way to much hence why setting back to the original clearance.
@@sce8arl The correct value 0.2-0.3Nm. 🤔
@@ihabsglei apologies. That’s what I meant. The sensitivity of my torque wrench put way too much load on the belt hence why I stuck with the same clearance on disassembly.
Great stuff! Very gung ho. Thanks also for listing those bearing numbers😊
No problem. Glad you enjoyed it
Swell is horrorfing
I am doing this
So good even if you don’t like heights like me 😅
@@sce8arl I did it yesterday it was amazing
@@Denki_Kaminari669 Great isn’t it. I need to go again
@@sce8arlwhen did u go?
@@sce8arlI am a kid aswell and found it fun
Fantastic route
Such a great place
Only now seeing this Andy. Lush weather you guys had 😉👌🏽🤣🏴 bit different than Dave’s stag weekend 💪🏽
I know right! Didn’t stop.
That baboon looked like he wanted to hop on
🤣🤣. Scary
What levels are blues
From easy to difficult - green, blue, red, black, purple.
Hi Mate, how are you editing your footage what app your using to get it 4k on you tube
I now use splice on my iPhone. Download the 4k footage to your phone from the GoPro and then edit using splice.
How long did it take to get to the summit thanks
About 80 mins or so
@@sce8arl thanks for the reply buddy
💪🏼
Name of the trails?
@hein_mcleod Cross Downhill, Fart Squirrel and AC/DC predominantly
are you allowed to walk this route? the little bridge thing looks like a cute spot
You are. The area is for everyone to use which is great.
What's the width of your handlebars ? 😮
Ha. Narrow. Not a fan of wide bars
How tall are you ? Have you tried wide bars ?
Quite short. My ebike had wide bars. Cut them down too.
Sweeeeet
Didn't quite see what you did!
Line at 0:08 Needs a T shirt:
Where your bike slid, there's barbed wire. That could've been nasty. How's the ebike riding experience compared to a push bike? I'm looking in to getting an SL
They’re a complete game changer. Demoed the SL in Coed Y Brenin. Great bike.
I did it last year. Was disappointed by the amount of walking with the bikes we had to do on the same route. Looks like you have edited those bits out. Wouldnt do it again TBH as there are better rides in the area for eeebbbzzz.
For sure. Didn’t know what the trail was going to be like but was pretty good. Weather was shocking though!
Nice trails Mate,.. Good video shot,. enjoyed watching here,.stay safely ride 🚲🤗👍
Thanks bud
Awesome !
Thanks
Where was this ? I need to have a go ! Great video
Llandow circuit in South Wales 🏴
@@sce8arl next time let’s organise something.. even Francesco will join.. it will be massacre!!
This looks awesome!
Smashed it bud. 👍 the dust though 🤢
WHERE IS THIS?
Afan in the Neath valley in South Wales.
what size bullet casings and cufflink blanks did you use ? Did you use the flat cufflink blanks ?
They were 7.62 blanks with flat cufflink blanks. I can’t remember the length.
This looks amazing!!
Your mad great video
Epic trails
Lovely Video , what a great spot we have so close to the city!
Have you a strava or gpx for this route please.
I think I do.
Great technical abilities, be careful my friend.
What speed did you get for the downhill but
Just shy of 40mph I think.
Just checked Strava and it was 45 mph 🦾🦾
Yes that looked buggered know javea well been going for the last 8 years
Sweeeeeeet 👌🏼😉
Trail stupendo
Man I need to shop for some better clothes… and not slouch 😂
😅
Where the trail please
Steetley Quarry in Pentyrch.
I live on the road on the other side of this mountain. You have inspired me. So scary but worth it I assume.
Fantastic trail. I’d recommend walking it first.
@@sce8arl yes I definitely will. It looks pretty advanced. I drive alongside there daily. I never knew there was a trail there. It looks too steep for any sane person. Might just walk it and never gather the courage to ride it. 🤣 thanks again. :)
That was the first time I’d ridden it as well. Went in blindly having never walked it either. Is a tricky one. Luckily that was on the bike I’ve owned for years. Hired a hard tail and tried it a few years later and really struggled.
Awesome! Where did you start this route?
It starts at Cape San Antonio and drops down into Javea Port.
@@sce8arl Cheers. It looks like a fun route.
Absolutely amazing
ive not ridden badger and bodger for years i have been told its changed, if i head for the old trails will the new stuff be obvious or if not where do i find it.great video
If you drop down off the Garth and turn left you should find it. Head as far as you can go and you’ll find the entrance.
@@sce8arl thanks better wait for dry weather it looks steeper than the old one
@@st1ffee can be a bit tricky in the wet.
@@sce8arl thanks better wait for dry weather it looks steeper than the old trail
@@sce8arl I bet thanks again
What bike u riding it look nice
Specialized Stumpjumper expert carbon.